Create Presentation
Download Presentation

Download Presentation
## Chapter 10: Stresses and Deformations in Cylinders

- - - - - - - - - - - - - - - - - - - - - - - - - - - E N D - - - - - - - - - - - - - - - - - - - - - - - - - - -

**Chapter 10: Stresses and Deformations in Cylinders**In all things, success depends on previous preparation. And without such preparation there is sure to be failure. Confucius, Analects Common beverage can. Along with food containers, these are the most common pressure vessels. (AP/Wide World Photos)**Classes of Fit**Table 10.1: Classes of fit.**Recommended Tolerances**Table 10.2: Recommended tolerances in inchesfor classes of fit.**Recommended Tolerances**Table 10.3: Recommended tolerances in millimetersfor classes of fit.**Recommended Shaft and Hub Diameters**Table 10.4: Maximum and minimum diameters of shaft and hub for two types of fit.}**Thin-walled Pressure Vessel**Criterion for thin vs. thick wall: Stresses for thin-walled cylinder: Figure 10.1: Internally pressurized thin-walled cylinder. (a) Stress element on cylinder; (b) stresses acting on element.**Internally Pressurized Cylinder**Figure 10.2: Front view of internally pressurized, thin-walled cylinder.**Pressurized Cylinder**Figure 10.3: Complete front view of thick-walled cylinder internally and externally pressurized. (a) With stresses acting on cylinder; (b) detail of stresses acting on element. Figure 10.4: Cylindrical coordinate stress element before and after deformation.**Internally Pressurized Cylinder**Stress distribution: Maxima occur at r = ri: Radial displacement: Figure 10.5: Internally pressurized, thick-walled cylinder showing circumferential (hoop) and radial stress for various radii.**Externally Pressurized Cylinder**Stress distribution: Maxima: Figure 10.6: Externally pressurized, thick-walled cylinder showing circumferential (hoop) and radial stress for various radii.**Design Procedure 10.1: Stress Analysis of Thick-Walled**Cylinders • A common design problem is to determine the largest permissible external and/or internal pressure to which a cylinder can be subjected without failure. Axial stresses, if present, are negligibly small. The following design procedure is useful for such circumstances: • For internal pressurization, both the radial and circumferential stresses are largest at the inner radius. The von Mises stress for this plane stress case can be shown to be • so that the allowable internal pressure is, from Eq.~(6.8), • For external pressurization, it can be shown that the larger von Mises stress occurs at the inner radius, with the stresses of σr = 0 and σθgiven by Eq. (10.32). This yields an expression of allowable external pressure of: • For combined internal and external pressurization, Eqs. (10.20) and (10.22) need to be substituted into a failure criterion from Ch. 6, such as the DET given for plane stress in Eqs. (6.10) and (6.11).**Rotating Cylinder**Stresses: Figure 10.7: Stresses in rotating cylinder with central hole and no pressurization.**Rotating Solid Cylinder**Stresses: Figure 10.8: Stresses in rotating solid cylinder with no pressurization.**Interference Fit**For hub and shaft of the same material, and a solid shaft: Torque that can be transmitted: Figure 10.9: Side view showing interference in press fit of hollow shaft to hub.**Interference Fit**Figure 10.10: Front view showing (a) cylinder assembled with an interference fit and (b) hub and hollow shaft disassembled (also showing interference pressure).**Example 10.10**Figure 10.11: (a) Block placed between two rigid jaws of clamp, and (b) associated forces.**Die Casting Machine**Figure 10.11: Schematic illustration of a die casting machine. Source:From Kalpakjian and Schmid [2010].